Self-adhesive packaging material INOTACK INTRODUCTION INOAC CORPORATION Package Dept. General Pacakaging Material Carton Box PE Foam PE Bag AIR BOBBLE Takes Time Packaging Attached by Troublesome to tape Various Tape Claim for Taping 。（ Scratch ） Ship Out 1
Merit of INOTACK １． Without Tape and string, Cold Seal side attach together. ２． Various composite(Different Surface material) Type （ Ex. Common, Piercing resistant, a half transparent. Etc. Type ） ３． Possibly reduce Total Cost (Operation process reduction, labor cost etc). ４． Possibly better item quality assurance. (Less possible item damage Function of INOTACK １． Packaging ２． Banding ３． Protective cushion ４ . Surface protection 2
Specification Surface Material Foam １／１６“（ 1.6 ㎜） ３／３２”（ 2.4 ㎜） ポリプロピレンフォーム（ＰＰ１００ Exp ） Special adhesive Self Cold Seal ＜ Table 1 ＞ Cold seal Foam Craft Surface Material: Craft paper, Liner board, Film, Unwoven are availabl NVL Type Craft paper etc. （ Craft ７５ g/ ㎡ ＮＶＬ－７５・ＰＥ クロス Ｎ V Ｌ－ＣＰ５０ etc ） Special Adhesive Self Cold Seal ＜ Table 2 ＞ Craft paper Self Cold Seal 商品 × Without Foam ⇒ NVL 3
NVL -2 ＷＡＸ Coating ＷＡＸ Craft Paper （ Craft Paper ５０ g/ ㎡ ＮＶＬ－５０Ａ・ Craft Paper ７０ g/ ㎡ ＮＶＬ－７０Ｃ 等） Special Adhesive Self Cold adhesive Corrugated ＜ Table 3 ＞ Box クラフト紙表面にＷＡＸを塗工する事 WAX Coating Craft によって、クラフト紙の耐摩耗性を Self Adhesive × 商品 アップする事で、商品を守ります。 【 Application and Merit 】 １） Packaging ・ Easy to cover/packaging without tape ITEM CODE ＜ Ex ： PC ＃３０ 1/16” ・ PC100 3/32”OPP‐SC etc. ＞ Point 4
【 Application Merit 】 ２） Banding ・ No Separator and No peeling Separator ・ No Separator garbage Label application ITEM CODE ＜ Ex ： PC030 1/16”NW‐2 ・ PC025 1/16”PET. ect ＞ Banding for Wire Harness 【 Application and Merit 】 ３） Surface Scratch Protection ・ Painting Plastic parts (Especial Automotive Exterior Parts etc.) ＜ Application ＞ ・ Bumper ・ Spoiler ITEM Code ＜ Ex ： NVL ・ PC075 1/16”CPI etc. ） 5
【 Application and Merit 】 ４） Cushion ・ It is good cushion with 100 Expansion Polypropylene Foaming ５） Air-Tightness ・ PP foam is Closed Cell which is excellent water resistance and humidity resistance ＜ Closed Cell feature is good water reflection ＞ 【 Application Graph per Industry 】 Auto 分野別採用 Furniture Housing OA Other 6
Fabrication １） Cut Cut into desirable size ２） Slitting Min １５ｍｍ width and rewinding ３） Pressing Cut into various shape ４） Printing (Craft Type) 【 Frequent Question 】 １． Roll Size ：９１０㎜ etc. ×２１０Ｍ（ Please refer Catalog ） ３． General Cost Idea （ Against Carton box : 3x higher/ Against Air Bubble: 5 x Higher ） ４． It is a insulator, thus cause static ５． There is no anti-rust Time ６． Static Friction Coefficient ｔａｎ θ ＝６７゜ （ Not Slippery ） ７． Heat Resistance Temperature : It depends on type but cold seal adhesive start to get soften over 70C. 7
【 Handling Caution 】 １． Do not touch cold seal surface by hand. （ It will bring adhesive bonding weaker by hand oil/sweat ２． Please do not attach machinery grease, Separator chemical, organic solvent over cold seal surface 。 ３． Please do not expose cold seal surface （ No direct Sun light) ４． Please do not get cold seal surface wet （ but once it dries out, it can attach again) ） ５． Please do not Keep under high temperature, high humid. （ No More than ７０ ℃ ） ６． It tends not to attach together under law temperature （ Please use more than and equal to 5C ） Inotack adhesion may be weaken or not attach together due to above. Handling Caution １） Adhesive side is weak against ultra violet ray Keep Craft paper face up -Face down foam-surface ク ラ -Keep in Dark フ × ト 面 ２） Adhesive migration が 表 - Do not wrap Silver ・ Copper directly 側 -Test/evaluation is required for PVC because plasticizer influence PVC as well as unvulcanized Rubber 8
Recommend
More recommend
